User Manual Manual number: PTI-06-07/02/08/A Retail scales (RS232 version) WTC 6/S, WTC 15/S, WTC 30/S WTC 6/SW, WTC 15/SW, WTC 30/SW
12. USER MENU 12.1. List of scale menu groups Menu is divided into 3 basic groups. Each group has individual name starting from capital letter P.
12.2.2. Return to weighing function Inserted changes in scale memory will be saved after return to weighing with procedure of saving changes. Pre
After placing the load, scale display will indicate net mass. Tarring can be done many times in full measuring range of scale. While using the tare
14.1. Setting the filter level Procedure: • Enter to submenu <P1. rEAd> according to point 12.2 of manual, and next: 0 - 4 - filter le
Fnnd OFF - median filter operation on Fnnd On - median filter operation off Return to weighing: See – point 12.2.2. – return to weighing.
Example of that can be very slow loading of pan (e.g. load pouring ), in such case correction of zero indication can also correct indication of real
Transmission parameters programmed in scale: • Transmission baud rate - from 1200 to 57600 bit/s • Data bits - 8 • Stop bit - 1 • Parity control
Prn StAb - Printout of stable weighing results Prn Cnt - Continuous transmission Return to weighing: See – point 12.2.2. – return to weighing. 15
16. OTHER PARAMETERS User can set parameters which have influence on operation of scale, e.g. backlight, „beep” signal. These parameters are in grou
Notice: For setting bL=Auto, when result doesn’t change in about 10s, backlight will be switched off. Backlight is switched on automatically when in
Contents 1. APPLICATION ... 3 2.
17. FUNCTIONS OF COMPUTING SCALES User of retail scales series WTC has possibility of using following computing functions: • Direct inserting of u
After inserting price wait about 5s, now it is possible to insert new price without cancellation of previous on with key . 17.2. Saving unit price
17.3. Recalling of saved unit price User has possibility to recall unit price from data base by choice of goods number PLU, to which unit price is
18. COOPERATION WITH PRINTER Signal with current display state is sent each time key is pressed. Scale can cooperate with one of thermal printer
Cable scheme: Cable scheme: scale –computer 20. COOPERATION WITH CASH REGISTERS Retail scales series WTC cooperate with most of cash registers
21. COMMUNICATION PROTOCOL 21.1. General information A. A character protocol scale-terminal has been designed for communication between RADWAG sca
21.3. Response message format After sending a request message you can receive: XX_A CR LF command accepted and in progress XX_D CR LF command co
T_A CR LF T_v CR LF - command accepted and in progress - command comprehended but tare range exceeded T_A CR LF T_E CR LF - command accepted and in p
Frame format: 1 2 3 4 5 6-14 15 16-21 22 23-30 31 32 S I space Stability mark mark mass space price space charge CR LF Example: S I CR
21.5. Manual printout User can generate printouts from scale manually when indication is stable after pressing key . Printout format 1 2 3-11 12
1. APPLICATION Retail scale WTC type is a perfect weighing device for application in small and standard trade. power supply by inbuilt batteries all
21.6. Continuous transmission Indicator has possibility of mass printout in continuous transmission. Transmission mode can be switched on with comma
22. ERROR MESSAGES Err2 - Value beyond zero range Err3 - Value beyond tare range Err8 - Exceeded time of tar ring/zeroing operation null - Trans
MANUFACTURER OF ELECTRONIC WEIGHING INSTRUMENTS ZMP ,,RADWAG” 26 – 600 Radom, Bracka 28 Street POLAND Tel. +48 48 38 48 800, tel./fax. +
G. In case of failure, immediately disconnect scale power supply; H. Devices that are to be withdrawn from usage should be utilized according to
4. DIMENSIONS Dimensions of scales in WTC/S series Dimensions of scales in WTC/SW series 5. SCALES ASSEMBLY Remove the scale from factory pa
• Install the pan and the pillar (WTC/SW scales) according to below drawing: Assembly of scales WTC/S series Assembly of scales WTC/SW series
• Turn on the supply with switch , • After turning on the supply, wait until scale test is finished, • When scale test is finished in display w
Connect to scale A/C adaptor to recharge accumulator and restart the device with switch . 8. SCALE KEYBOARD 9. SCALE DISPLAY Display of scal
10. KEYS FUNCTIONS Enter to recalling unit price Enter to saving unit price Zeroing of scale Tarring of scale or confirmation of current operati
Comments to this Manuals